Skip to main content
You have permission to edit this article.
Install a frost-proof sillcock to keep keep pipes from freezing

Install a frost-proof sillcock to keep keep pipes from freezing

  • Updated
  • 0


For AP Weekly Features

Growing up in the West, except for the occasional trip to the mountains for a day or so of frolicking, we saw little snow. As children, we associated snow with fun and pleasure. It wasn't until later that less pleasurable aspects of snow, such as shoveling and dealing with ice dams, came to light.

We then became familiar with a device that we had never before seen - a frost-proof sillcock. We learned that a sillcock is an outdoor water faucet or "hose bib." What we had yet to understand was how a hose bib could be frost-proof. After all, on those rare occasions when the mercury dipped low enough to be a threat, we simply wrapped the hose bib and adjacent pipes with rags to prevent the pipes from freezing and, thus, bursting.

A sillcock is just another name for a hose bib. It is called by that name because it is typically located just above the sill - the board that is anchored to the top of a foundation. It also is mounted to the header joist which in some parts of the country is referred to as the sill. In other regions, it's called the rim joist.

The pipe that supplies water to the sillcock has a shut-off valve located in the basement some distance in from the exterior wall. Thus, when the weather gets cold, the valve can be turned off and drained to prevent a burst pipe. Although it's a reasonably good means of prevention, it can be somewhat inconvenient. And what happens when one forgets to close the shut-off valve and drain the pipe? The consequences can be disastrous.

Enter the frost-proof sillcock. It looks much like your run-of-the-mill hose bib except for the vacuum breaker that sits atop the valve. When a frost-proof sillcock is turned off, air rushes into the sillcock through the vacuum breaker to break the seal of water and help the residual amount to drain.

What is more amazing is what one can't readily see. Unlike a traditional hose bib where the valve stem is an inch or two in length, the valve stem for a sillcock is 6 inches to 30 inches long. Thus, the valve is well within the exterior wall and protected from the cold and freezing. What's more, you don't need to worry about whether you remembered to close the shut-off valve, since one isn't required.

Installing a frost-proof sillcock is reasonably simple especially if you have previous experience soldering. Besides the sillcock, you'll need a torch, solder, flux, a flux brush, fine sandpaper or steel wool, a copper tubing cutter and a rag. Start by removing the existing sillcock. Close the shut-off valve and drain residual water from the faucet. Adjust the tubing cutter to surround the pipe and tighten the handle while rotating the cutter around the pipe. Remove the old sillcock and position the new frost-proof one in its place. Check the length of the supply line, make a pencil mark and - using the tubing cutter - cut the pipe again to correspond with the length of the new sillcock.

Use fine sandpaper or steel wool to polish the end of the water supply and the inside of the copper fitting at the end of the sillcock. Apply a small amount of flux (soldering acid) to both the end of the supply line and the interior of the fitting at the end of the sillcock, and join the two. Next, light the torch and, with the torch in one hand and a length of solder in the other, apply the tip of the flame to the fitting at the end of the sillcock. Be sure that the sillcock valve is open all the way to prevent damage to rubber gaskets from the heat. Place the tip of the solder at the joint between the pipe and the fitting and continue to apply heat until the solder is drawn into the joint. Move the tip of the solder around the joint and remove the flame to prevent the pipe from overheating. Use just enough heat to cause the solder to flow. Immediately after removing the flame, use the flux brush to apply a small amount of flux around the entire joint.

Turn the torch off and allow the fitting to cool. Use a rag to remove excess flux, and clean the joint. Finish the job by fastening the sillcock flange to the exterior siding with a couple of screws. First, apply a generous bead of caulk between the siding and the flange for a good waterproof seal. Turn on the water supply (once and for all) and flush the new sillcock before turning it off.

For more home-improvement tips and information, visit the Web at:


Be the first to know

* I understand and agree that registration on or use of this site constitutes agreement to its user agreement and privacy policy.

Related to this story

Most Popular

Get up-to-the-minute news sent straight to your device.


News Alert

Breaking News